Search found 20 matches
- Mon Oct 21, 2019 1:11 pm
- Forum: Diagnostics using the USB Autoscope device
- Topic: Flexray
- Replies: 5
- Views: 62824
Re: Flexray
Hello friend ZAP !!!! I would like to know more about this interesting topic. Do you have more information about this measurement? Hey Jorge, Unfortunately, I don't have anything new to report. I did buy a set of cheap attenuated test probes, ( https://www.ebay.com/p/2229729394 ) but I haven't had ...
- Fri Apr 26, 2019 2:16 am
- Forum: Diagnostics using the USB Autoscope device
- Topic: Flexray
- Replies: 5
- Views: 62824
Flexray
So, I had a 17 Audi Q7 come in today with communication codes. I attempted to scope the network lines, and this is what I got: flexray.png The picture above is with the sampling rate maxed out at 5Ms. I tried switching to a single channel and cranking it up to 12.5Ms. Below is what I got: max sampli...
- Mon Apr 22, 2019 9:34 pm
- Forum: Diagnostics using the USB Autoscope device
- Topic: Attenuators?
- Replies: 1
- Views: 30131
Attenuators?
Over the weekend, I was attempting to check primary ignition voltage on a 2002 Porsche 996 with the 3.6L engine. I was surprised that the level-over-range warning was going off with the vehicle idling. Apparently this vehicle has very high voltage on the primary side. Does Autoscope sell attenuators...
- Tue Mar 12, 2019 3:16 am
- Forum: Diagnostics using the USB Autoscope device
- Topic: Secondary ignition on vehicles with individual coils
- Replies: 3
- Views: 33632
Re: Secondary ignition on vehicles with individual coils
Oh, okay. Thank you for the education! When checking secondary ignition, I try to (when possible) load the engine by power braking. (putting the vehicle in gear and applying the throttle while holding the brakes) Is there a tool or fixture that could be used to hold the Lx-M against the ignition coi...
- Tue Mar 12, 2019 3:00 am
- Forum: Diagnosing with the CSS script
- Topic: CSS graph goes off top and bottom of screen
- Replies: 2
- Views: 27603
Re: CSS graph goes off top and bottom of screen
Great. Thank you!
I haven't tried the Beta, I'll check it out.
I haven't tried the Beta, I'll check it out.
- Sun Mar 10, 2019 3:28 am
- Forum: Diagnosing with the CSS script
- Topic: CSS graph goes off top and bottom of screen
- Replies: 2
- Views: 27603
CSS graph goes off top and bottom of screen
I've had this issue a few times, where the graph in the CSS script will go way off the top and/or bottom of the screen.
Has anyone else run into this? Is there a way to zoom out further?
Has anyone else run into this? Is there a way to zoom out further?
- Thu Mar 07, 2019 11:03 pm
- Forum: Diagnostics using the USB Autoscope device
- Topic: Secondary ignition on vehicles with individual coils
- Replies: 3
- Views: 33632
Secondary ignition on vehicles with individual coils
Most of the vehicles I work on have individual ignition coils. I'll usually start by hooking the red Cx leads up to cylinders 1-3, then switching the last clamp between cylinders 3 and 4. This isn't the end of the world, but it would be nice to be able to watch all 4 cylinders at the same time. Is t...
- Sun Jan 27, 2019 5:25 pm
- Forum: Diagnostics using the USB Autoscope device
- Topic: Zeroing the CTi-M
- Replies: 12
- Views: 68741
Re: Zeroing the CTi-M
Okay, interesting. I'll keep in eye out for that.
- Sun Jan 27, 2019 3:08 pm
- Forum: Diagnostics using the USB Autoscope device
- Topic: Zeroing the CTi-M
- Replies: 12
- Views: 68741
Re: Zeroing the CTi-M
Do you mean the white LEDs inside the jaws? I've never noticed them blinking before.When LED blinks, it means that clamps can not calibrate.
- Mon Dec 31, 2018 1:06 pm
- Forum: Diagnostics using the USB Autoscope device
- Topic: Adding notes to waveform files?
- Replies: 2
- Views: 30392
Re: Adding notes to waveform files?
Great, thank you.
I wish I had asked this question a long time ago. I have a bunch of waveforms that I can't remember anything about...
I wish I had asked this question a long time ago. I have a bunch of waveforms that I can't remember anything about...